For many years, the construction industry in Sweden has not developed much of an integral approach for design across disciplines. The sector?s impact on society, economics and environment is huge. To make the interactions within the construction industry more efficient, a relatively new concept called BIM (Building Information Modeling) has been introduced. The idea with BIM is that the different actors of the construction industry will work through intelligent CAD software, with common file formats and more cooperation between different actors during the various steps of the building and construction process.The technical consultancy company WSP Sweden is working actively to implement BIM within the frame of its activities.

This master thesis is developed based on the desire of the water and sewage department in the municipality of Karlskrona. The department, which vouches for the quality of produced drinking water and sewage cleaning, was in need of help dealing with risk analysis.The water and sewage department is obliged to identify and assess risks according to Swedish legislation. However, no guides for this purpose regarding safety, health, environment and quality were available. The aim of this report was to accomplish a guideline for the performance of risk analysis within water and sewage plants. If the guideline is used, the requirements in the legislation will be obtained.

This report is about the impact climate change has on the water and sewage systems in general, and the situation in the municipality of Karlstad in particular. Which vulnerabilities are linked to water and sewage systems with regard to climate change and extreme weather situations, what are the possibilities to adapt the system to this and what significance does climate adaptation of the water and sewage systems have in relation to sustainable development?To answer these questions I have studied literature on the subject and interviewed several people who work with these types of questions. The answers I have received state that there are a multitude of vulnerabilities linked to the water- and sewage systems, but that there are also many strong interests which strive to take measures and adapt to a changed climate. I have also come to the conclusion that the starting points and views of the possibilities to act differs between the people that I have interviewed, but that theses problems are built into the concept of democracy..

This report is commissioned by the Water and Sewage Agency in The City of Mariehamn, Åland. The basic aim is to investigate positive or negative effects of a relocation of the sewage pipe from a wastewater treatment plant, Lotsbroverket. The environmental licence of Lotsbroverket is to be revised and The Environmental Appeal Board at Åland?s Government and Administrative Board has made demands that several possible locations in an outer water area should be examined. The present location of the sewage pipe is in Svibyviken, which has been classified as an ?inner water area?.The objective of this work is to study to which extent the nutrient loading from Lotsbroverket influence the environmental conditions in Svibyviken, and to investigate the suitability of different locations of the wastewater pipe from Lotsbroverket.The way a coastal area looks, i.e., its morphometry, determines to a large extent its ecological characteristics.

The management of water resources and waste water varies between the countries of the EU. For many years, a large part of the water in Europe has been contaminated by, among other things, insufficiently treated waste water and emissions from agriculture. The EU Water Framework Directive 2000/60/EC and the Urban Waste Water Directive 91/271/EEC are intended to harmonize fresh-water management and waste water management within the whole EU, aiming at safeguarding drinking water of good quality and a high quality of all water within the EU today and in the future. There are however some problems concerning the waste-water directive. One problem is the huge investment needed in Slovakia to fulfil the demands of the waste-water directive for waste-water management in larger communities (with more than 2000 inhabitants).

Ground construction has to a large extent been dominated by traditional meth-ods during the last 50 years. Although the construction has been changed meanwhile innovations are not accepted. In collaboration with NCC Ltd Region South, I have examined a modern con-struction methodology that has been developed by NCC for future large pro-jects. The method is divided into two central phases. Phase 1 is? Single Pro-duction? which is a preliminary period for ground constructions to come.

Discharge of inadequately treated waste water containing nutrients such as phosphorus and nitrogen as well as organic matter and bacteria is associated with a risk of eutrophication and contamination. The Swedish government has decided upon several Environmental Quality Objectives aiming to reduce the emissions of nutrients to water bodies.In Sweden, there are between 675 000 to 1 000 000 on-site sewage systems. Recent studies have shown that the function of small sewage treatment plants is in many cases insufficient. To prevent this regular service and supervision by a professional is needed. The focus of this study are small sewage treatment plants which use a technique where mechanical, chemical and/or biological reduction of pollutants is being used in the same facility to reduce nutrients in household wastewater.The aim of the study is to investigate how different municipalities ensure that small sewage treatment plants fulfill the requirements and reduce pollutants as efficient as the manufacturers claim.

The aim of this project was to describe and to evaluate five small sewage treatment plants in the municipality of Laholm, Sweden, in order to investigate the treatment efficiency and to evaluate if effluents comply with discharge permits. The treatment systems were designed to treat effluents from 90 to 500 population equivalents. A report on the design and the present state of each sewage treatment plant has been made. This was made based upon previous documentation on water quality and by new sampling campaign as there were only a few previous measurements. Data has been evaluated and remedial actions proposed for those treatment plants that don?t fulfill discharge permits.

The master thesis, conducted at Metrima AB, concerns the development of a non-intrusivedistribution meter as a basis for individual tap water billing in apartments.The project is conducted in response to the market interest in individual tap water billing inapartments as an answer to environmental concerns regarding water consumption. Due to thehigh installation cost of traditional water meters, a new method of determining waterconsumption, without having to cut water pipes, is proposed.The proposed method distributes the total water consumption for an apartment complex toindividual apartments according to distribution meters, measuring water run-time, in eachapartment. The water run-time is estimated by measuring the water pipe?s outward vibrationsand temperature changes.A test environment was established and a prototype built, using a tilt- and vibration sensor forvibration sensing and a precision temperature sensor to measure temperature changes. As bothsensors work well in the test environment, further testing was done in 3 apartments for aduration of 5 days.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.